Solar Collectors: Different Types and Fields of Application

Swimming pool absorbers, on the other hand, are usually made of plastic (mostly EPDM, but also of polypropylene and polyethylene), as the lower temperatures involved do not require greater heat capacity.

Heating and storage are united in a reservoir collector. Arrays of reservoir collectors do not need circulating pumps or regulating mechanisms, as the drinking water is warmed and stored right in the collector.

Highly efficient absorber surfaces

Absorbers are usually black, as dark surfaces demonstrate a particularly high degree of light absorption. The level of absorption indicates the amount of short-wave solar radiation being absorbed that means not being reflected. As the absorber warms up to a temperature higher than the ambient temperature, it gives off a great part of the accumulated solar energy in form of long-wave heat rays. The ratio of absorbed energy to emitted heat is indicated by the degree of emission.

In order to reduce energy loss through heat emission, the most efficient absorbers have a selective surface coating. This coating enables the conversion of a high proportion of the solar radiation into heat, simultaneously reducing the emission of heat.

The usual coatings provide a degree of absorption of over 90%. Solar paints which can be mechanically applied to the absorbers (with either brushes or sprays), are less or not at all selective, as they have a high level of emission. Galvanically applied selective coatings include black chrome, black nickel, and aluminum oxide with nickel. Relatively new is a titanium-nitride-oxide layer, which is applied via steam in a vacuum process. This type of coating stands out not only because of its quite low emission rates, but also because its production is emission-free and energy-efficient.

Flat-plate Collectors

A flat-plate collector consists of an absorber, a transparent cover, a frame, and insulation. Usually an iron-poor solar safety glass is used as a transparent cover, as it transmits a great amount of the short-wave light spectrum.

 

Sketch of a flat-plate collector

Simultaneously, only very little of the heat emitted by the absorber escapes the cover (greenhouse effect).

In addition, the transparent cover prevents wind and breezes from carrying the collected heat away (convection). Together with the frame, the cover protects the absorber from adverse weather conditions. Typical frame materials include aluminum and galvanized steel; sometimes fiberglass-reinforced plastic is used.

The insulation on the back of the absorber and on the side walls lessens the heat loss through conduction. Insulation is usually of polyurethane foam or mineral wool, though sometimes mineral fiber insulating materials like glass wool, rock wool, glass fiber or fiberglass are used.

Flat collectors demonstrate a good price-performance ratio, as well as a broad range of mounting possibilities (on the roof, in the roof itself, or unattached).

In order to reduce heat loss within the frame by convection, the air can be pumped out of the collector tubes. Such collectors then can be called evacuated-tube collectors. They must be re-evacuated once every one to three years.

In this type of vacuum collector, the absorber strip is located in an evacuated and pressure proof glass tube. The heat transfer fluid flows through the absorber directly in a U-tube or in countercurrent in a tube-in-tube system. Several single tubes, serially interconnected, or tubes connected to each other via manifold, make up the solar collector. A heat pipe collector incorporates a special fluid which begins to vaporize even at low temperatures. The steam rises in the individual heat pipes and warms up the carrier fluid in the main pipe by means of a heat exchanger. The condensed liquid then flows back into the base of the heat pipe.

Sketch of a heat pipe collector

The pipes must be angled at a specific degree above horizontal so that the process of vaporizing and condensing functions. There are two types of collector connection to the solar circulation system. Either the heat exchanger extends directly into the manifold ("wet connection") or it is connected to the manifold by a heat-conducting material ("dry connection"). A "dry connection" allows to exchange individual tubes without emptying the entire system of its fluid. Evacuted tubes offer the advantage that they work efficiently with high absorber temperatures and with low radiation. Higher temperatures also may be obtained for applications such as hot water heating, steam production, and air conditioning.

How much energy does a solar collector provide?

The efficiency of a solar collector is defined as the quotient of usable thermal energy versus received solar energy. Besides thermal loss there alwas is optical loss as well. The conversion factor or optical efficiency h0 indicates the percentage of the solar rays penetrating the transparent cover of the collector (transmission) and the percentage being absorbed. Basically, it is the product of the rate of transmission of the cover and the absorption rate of the absorber.

Efficiency graph of solar collector performance

The heat loss is indicated by the thermal loss factor or k-value. This is given in watt per m² collector surface and the particular temperature difference (in °C) between the absorber and its surroundings. The higher the temperature difference, the more heat is lost. Above a specific temperature difference, the amount of heat loss equals the energy yield of the collector, so that no energy at all is delivered to the solar circulation system.
A good collector will have a high conversion factor and a low k-value.

Which collector is suitable for which situation?

The desired temperature range of the material to be heated is the most important factor in choosing the correct type of collector. An uncovered absorber is certainly not suitable for producing process heat. The amount of radiation on that spot, exposure to storms, and the amount of space must all be carefully considered when planning a solar array.

Graph of efficiency and temperature ranges of various types of collectors (radiation: 1000 W/m²)

The specific costs of collectors are also important. Evacuated-tube collectors are substantially more expensive (at 511,29 - 1278,23 Euro /m² collector surface) than flat-plate collectors (153,34 to 613,55 Euro /m²) or even plastic absorbers (25,60 to 102,26 Euro /m²). However, a good collector does not guarantee a good solar system. Rather, all components should be of high quality and similar capacity and strength.

Text and graphics by permission of the:
Deutschen Gesellschaft für Sonnenenergie e.V -- German Society for Solar Energy.

Concise and comprehensible explanations of the basic concepts in solar heating and photovoltaics can be found in our Solar-Lexicon.

Reports on technology, business and politics, as well as presentations on innovative systems and products can be found in the Solar Magazine